Manuall Trade Library Run your shop on Manuall

Commercial Floor Stripping + Waxing

SOP Process Updated Jun 19, 2026 · Cleaning

Purpose

Define the commercial VCT (vinyl composition tile) strip + wax service - the highest-margin recurring service in commercial janitorial. Per-square-foot pricing.25 stripping, finish coats. A 5,000 sq ft retail floor runs per service, performed annually or quarterly. Done wrong, the customer sees yellow streaks, swirl marks, or finish failure within weeks + you eat the do-over.

Scope

Applies to:

  • Commercial VCT floors (retail, office, school, medical)
  • Sheet vinyl (similar process, fewer coats)
  • Polished concrete (different process - DO NOT apply finish)

Excludes: wood floors, terrazzo (specialty), epoxy (don't strip - clean only), LVT (luxury vinyl tile - most LVT manufacturers prohibit stripping; check manufacturer spec).

Responsibilities

  • Lead floor tech runs the chemistry + machine work
  • Helper handles cone setup, wet-vac, baseboards
  • Customer must vacate the area for 6 - 10 hours (cure time)

Procedure

Prep (60 - 90 minutes for 5,000 sq ft)

  1. Move all furniture, signage, displays. Photograph original positions.
  2. Dust mop the entire area. Then damp mop with clean water to lift fine dust.
  3. Mask baseboards, door thresholds, carpeted transitions with painter's tape + plastic.
  4. Set wet-floor cones at every approach. Lock doors if possible.
  5. Mix stripper per manufacturer spec - typically 1:4 with cold water (hot water flashes the stripper). Common products: Hillyard Top Clean, Spartan SparClean, Diversey Pro Strip.

Strip (90 - 180 minutes)

  1. Apply stripper solution generously with a mop. Work in 10 ft × 10 ft sections.
  2. Dwell 10 - 15 minutes. The floor should stay wet - re-apply if drying.
  3. Agitate with 175 rpm rotary buffer + black stripping pad. Two passes minimum.
  4. Wet-vac the slurry. DO NOT mop it - old finish is in suspension; mopping spreads it.
  5. Rinse with clean water + neutralizer (red-pad or clean mop pass). Two clean rinses.
  6. Check for residue: a black square on the floor should rub up with a clean white towel without picking up gray streaks. If gray, rinse again.

Apply finish (60 - 120 minutes)

  1. Allow floor to dry completely (30 - 60 minutes; pH-test if unsure).
  2. Use a clean wax mop dedicated to finish only (never the strip mop).
  3. Apply thin even coats. Start at far wall; work toward the door.
  4. Standard build: 4 - 5 coats. High-traffic retail: 6 - 8 coats. Each coat 18 - 22% solids.
  5. Dry time between coats: 30 - 45 minutes. Check by touch - tacky is not dry.
  6. Final cure: 6 - 8 hours before light foot traffic; 24 hours before furniture.

The single biggest predictor of a clean finish is the RINSE step, not the strip step. Old finish residue left under the new coats turns yellow within 2 weeks + customers blame you. Rinse twice + verify with the white-towel test before applying the first finish coat. Cheap insurance.

Acceptance Criteria

  • Floor evenly glossy; no yellow streaks or swirl marks
  • No finish on baseboards or door thresholds
  • Furniture returned to original position (use the prep photos)
  • Customer walks the floor + signs the field report
  • Cure-time + traffic warnings communicated in writing

Safety

  • Stripper is high-alkaline (pH 12 - 13); wear chemical-resistant gloves + eye protection
  • Wet floors are slip hazards; cones + barricades, no exceptions
  • Ventilate - open exterior doors when possible; some strippers off-gas
  • Lock-out / wet-vac the area from public access throughout the cure window

References

  • ISSA Cleaning Industry Management Standard, Floor Care section
  • Manufacturer technical data sheets (Hillyard, Spartan, Diversey)
  • OSHA 1910.22 (walking-working surfaces - slip hazards)
  • Manuall internal: Commercial Cleaning Specification Reference, Cleaning Equipment Investment Guide

Related articles